Fast, Reliable Gate Parts & Welding Across Burlingame
Gate parts and welding in Burlingame, CA typically runs $180–$650 depending on the repair, and our Gate Parts & Welding team can usually diagnose and quote same-day. Louis and the Granite Gate team have worked on gates throughout Burlingame’s historic neighborhoods for 14 years, from the Craftsman homes of Easton Addition to the hillside properties above Skyline Boulevard. We carry sealed-bearing rollers, stainless steel hinges, and galvanized posts specifically selected for Burlingame’s salt-air climate, so we’re not ordering parts while your gate hangs open. Call (888) 416-1369 for a free estimate.
Why Granite Gate Repair California Is Burlingame’s Preferred Gate Parts & Welding Company
We’ve earned 197 verified reviews averaging 4.7 stars across the Bay Area, and a meaningful share of those come from Burlingame homeowners who found us after a general handyman couldn’t source the right hinge or match their ornamental ironwork. Louis Barrera still works in the field as Founder & Master Technician, which means the person quoting your job in Burlingame Park or Ray Park actually understands weld penetration and operator torque specs, not just sales margins.
Our response time to Burlingame averages same-day or next-morning, depending on part availability. Because we stock components for nine major brands — including FAAC, BFT, Linear, and Viking — we rarely need to special-order what your gate needs. That matters in Burlingame, where a sagging side gate or failed operator isn’t just an access problem; it’s a direct security exposure on a property where architectural integrity matters to resale value.
We know the local conditions. The marine layer that rolls off San Francisco Bay and blankets Burlingame most mornings isn’t just fog; it’s corrosive, salt-laden moisture that destroys uncoated hardware. We’ve replaced enough rusted hinge assemblies on Broadway and in the Burlingame Hills to know that standard carbon-steel parts installed here without proper sealing are a 3-year problem, not a 10-year solution.
Our Gate Parts & Welding Services in Burlingame
Hinge Replacement
Hinge replacement is our most frequent gate parts call in Burlingame, and there’s a specific reason why. The salt-laden air from San Francisco Bay accelerates corrosion on uncoated iron hinges, causing gates to sag or stick within 3-5 years of installation. In Burlingame’s historic neighborhoods — Burlingame Park, Easton Addition, and Ray Park — homeowners with original 1920s–1940s wrought-iron gates need hinges that match the period hardware while surviving the local climate. We stock stainless steel and hot-dip galvanized hinge assemblies rated for marine environments, and we weld mounting plates when the original jamb has deteriorated. A typical hinge replacement in Burlingame runs $180–$340.
Post Replacement
Gate posts in Burlingame take abuse from two directions: the same salt corrosion that attacks hinges, and the hillside settling common in Burlingame Hills properties where graded driveways shift seasonally. We replace steel and iron posts with galvanized or powder-coated alternatives, set in concrete footings deep enough to handle the lateral load of a heavy wrought-iron or wood gate. For historic homes where the post is integrated into masonry or stucco, we fabricate custom weld plates that preserve the original look. Post replacement in Burlingame typically costs $450–$850 depending on material, footing depth, and whether we need to match existing ornamental work.
Rail Repair
Horizontal rails on wood and metal gates crack, bow, or pull away from stiles over time — especially in Burlingame, where morning fog keeps wood swollen and metal expansion cycles active year-round. We repair split rails with sistered steel backing, re-weld separated joints on ornamental iron, and replace rotted wood rails with cedar or redwood that matches the original profile. When a rail has failed due to corrosion, we trace the cause; often it’s a drainage issue where the bottom rail sits in standing water from condensed fog. Rail repair in Burlingame generally runs $220–$480.
Custom Welding & Fabrication
Our in-house welding capability is what separates us from gate companies that subcontract metalwork. In Burlingame, where 1920s Spanish Colonial Revival and Tudor homes feature ornamental ironwork that owners want preserved, we fabricate replacement scrolls, finials, and pickets to match existing patterns. We recently replaced a rusted hinge assembly on a wrought-iron gate in the Burlingame Park neighborhood. The original LiftMaster operator was binding due to corroded rollers; we swapped them with sealed bearings and installed a new linear limit switch to handle the steep driveway grade typical of Burlingame Hills properties. Custom welding projects in Burlingame start around $350 for simple repairs and range to $1,200+ for full panel fabrication or ornamental matching.
Gate Rollers
Sliding gate rollers fail predictably in Burlingame’s climate: unsealed bearings ingest moisture from fog and condensation, then seize or grind flat. We install sealed-bearing or polymer rollers rated for wet environments, and we keep common sizes in stock for brands like FAAC and BFT so you’re not waiting on shipping. For hillside properties where the gate track has settled or warped, we re-weld or replace track sections and adjust roller spacing to restore smooth travel. Roller replacement in Burlingame runs $160–$320 per gate.
Latch & Lock Hardware
Corroded latches are a security issue we address regularly in Burlingame. The same salt air that rusts hinges attacks strike plates, deadbolts, and magnetic locks. We source marine-grade stainless latches and can weld custom catch boxes when the original jamb geometry doesn’t accommodate modern hardware. For automated gates, we integrate electric strikes and access control components with your existing operator. Latch and lock service in Burlingame typically costs $140–$280.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Burlingame
We maintain direct experience with nine gate automation brands, and we stock parts locally for the systems most common in Burlingame: FAAC, BFT, Linear, and Viking. FAAC and BFT operators are popular on higher-end Peninsula properties for their hydraulic reliability, but their circuit boards are vulnerable to moisture intrusion if the motor housing seal degrades — a failure mode we see accelerated by Burlingame’s persistent fog. Linear and Viking systems dominate residential installations here, and we carry limit switches, control boards, and gear assemblies for same-day repair. When we say “your brand, our specialty,” we mean we’ve actually torn down and rebuilt these units in Burlingame driveways, not just read the manual.
Common Gate Parts & Welding Problems We See in Burlingame Homes
- Salt air corrodes uncoated iron hinges and latch mechanisms. Gates in Burlingame Park and along the Bayfront sag or stick within 3-5 years of installation if standard carbon-steel hardware was used. We replace with stainless or galvanized equivalents and weld reinforcement plates where the jamb has deteriorated.
- Marine fog seeps into motor housings of gate operators. FAAC and BFT units are particularly susceptible if the gasket has aged; circuit board failure follows. We reseal housings, replace compromised gaskets, and install moisture-resistant control enclosures where needed.
- Steep hillside driveways in Burlingame Hills cause standard swing gates to bind on pavement. The grade is often steep enough that a flat-swing gate drags mid-arc. We specify raked-panel gates with higher-torque operators and set limit switches precisely to avoid motor burnout on the uphill pull.
- Original ornamental ironwork on 1920s–1940s homes cracks at weld joints. Decades of thermal cycling and corrosion fatigue cause failure at stress points. We grind, preheat, and re-weld with matching filler metal, then apply cold-galvanizing compound to extend service life in the local climate.
Pricing for Gate Parts & Welding in Burlingame, CA
Here’s what we typically charge for gate parts and welding work in Burlingame. These ranges reflect our 14 years of pricing jobs in this specific market — not national averages.
| Service | Typical Range in Burlingame |
|---|---|
| Hinge Replacement (pair) | $180 – $340 |
| Gate Roller Replacement (set) | $160 – $320 |
| Rail Repair / Sistering | $220 – $480 |
| Post Replacement (single) | $450 – $850 |
| Custom Welding / Fabrication | $350 – $1,200+ |
| Latch / Lock Hardware | $140 – $280 |
What moves the needle within these ranges? Material type (stainless vs. standard steel), access difficulty (hillside grades require more labor time), and whether we’re matching existing ornamental work that demands custom fabrication. We don’t markup parts — you pay our wholesale cost plus labor. Estimates are free, and we quote upfront before starting work. Call (888) 416-1369 for exact pricing on your specific gate.
We Also Serve Cities Near Burlingame
Our service radius covers the central Peninsula thoroughly. We regularly handle gate parts and welding calls in Hillsborough (where estate gates demand heavy-duty hardware), Millbrae, San Mateo, and San Bruno. If you’re in a neighboring city and found this page, we likely service your area — just call to confirm.
Serving Burlingame, CA — Our Local Coverage Area
We’re based in the Burlingame area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs — Gate Parts & Welding in Burlingame
Burlingame sits directly on the western shore of San Francisco Bay, exposing gate hardware to persistent salt-laden air and near-daily marine fog that inland Peninsula cities like San Mateo simply don’t experience at the same intensity. This means uncoated iron hinges in Burlingame corrode measurably faster, making stainless steel or galvanized upgrades a genuine necessity rather than an upsell. If your hinges are showing orange staining within 3-5 years, the salt air is the culprit. Call (888) 416-1369 and we’ll spec corrosion-resistant replacements that match your gate’s look.
Yes, custom welding and ornamental matching is a core capability we exercise regularly in Burlingame’s historic neighborhoods. We fabricate replacement scrolls, finials, and pickets to match existing patterns, then weld with appropriate filler metal and finish to blend with aged ironwork. We’ve restored gates in Burlingame Park and Easton Addition where owners specifically wanted to preserve period character for resale value. Bring us a photo or we’ll measure on-site — estimates are free.
Yes, it’s extremely common in Burlingame Hills where driveway grades are often steep enough that a standard flat-swing gate will drag or bind on the pavement mid-arc. The fix isn’t just adjusting the hinges; you need a raked-panel gate configuration and a higher-torque swing operator with limit switches set carefully to avoid motor burnout on the uphill pull. We’ve solved this exact problem on multiple hillside properties in the 94010 zip. Call (888) 416-1369 for an assessment.
In Burlingame’s fog-dense climate, we recommend lubricating rollers and hinges every 3-4 months with a marine-grade grease that won’t wash out with condensation. Standard lithium greases break down faster here than in drier inland areas. If you notice squeaking, sticking, or orange dust around hinge pins, you’re already overdue. We include lubrication service with most repair calls, or we can set up a maintenance schedule for properties with multiple gates.
Yes, FAAC operator failure after fog exposure is a pattern we diagnose and repair regularly in Burlingame. The moisture seeps past aged gaskets into the motor housing and corrodes the circuit board or limit switch contacts. We test the board, replace if necessary, reseal the housing with fresh gaskets, and often relocate the control box to a more protected position. Because we stock FAAC parts, most repairs are same-day. Call (888) 416-1369 — we’ll get your gate back in motion.
Ready to fix your gate? Louis and the Granite Gate team are available for same-day estimates throughout Burlingame and the Peninsula. Whether you need a single hinge replaced, a full ornamental iron panel fabricated, or a fog-damaged operator diagnosed, we’ll quote upfront and get the work done without subcontracting the welding. Call (888) 416-1369 for your free estimate.
Written by Louis Barrera, Owner at Granite Gate Repair California, serving Burlingame and the Bay Area since 2010.