Ghost Controls Gate Repair in Burbank, CA

Q: My Ghost Controls TSS1 keeps saying 'error 7' after the Santa Ana winds — is the motor burned out?

Usually not. Error 7 on a TSS1 typically indicates a limit-stop fault, and in Burbank that almost always means the nylon gear sheared from wind overswing. The motor itself is fine. We replace the gear with brass, reinforce the hinges, and recalibrate. Call (888) 416-1369 and we'll confirm with a quick diagnostic.

Q: I want to add a Ghost Controls keypad to my alley gate, but Burbank has its own building department — do I need a permit?

Yes. Burbank requires a permit for any new access control device that connects to an automatic operator, and the install must pass UL 325 inspection. We handle the paperwork and pre-check the work against Burbank's specific requirements so you don't fail on a technicality.

Q: My 1960s wrought-iron gate has rusted hinges and the Ghost Controls operator is struggling to move it — can you just replace the motor?

We could, but we'd be doing you wrong. A stronger motor will just destroy your gate frame. We cut out the corroded hinge pins, weld in new stainless hardware, and realign the gate first. Then the existing Ghost Controls operator, or a new one if needed, runs the way it was designed to.

Q: My Ghost Controls SSP slide gate on a rear alley in Burbank's Magnolia Park neighborhood won't close fully — is it the track?

Could be, but in Burbank we more often find silica dust and heat-corroded limit-switch contacts causing intermittent stop errors. We clean or replace the switch assembly and check track alignment. If the track itself is bent from a delivery truck backing into it, we weld and grind it true. Call (888) 416-1369 for a free diagnostic.

Q: I'm replacing my old Ghost Controls TSS2 with a new one — do I need a permit if it's the same model?

In Burbank, yes. Any automatic gate operator replacement requires a permit and inspection, even same-model swaps. The building department wants to verify current UL 325 compliance, which changes over time. We pull the permit, install to code, and coordinate the inspection so you're legal.

Ghost Controls Gate Repair in Burbank, CA | Granite Gate Repair California

Ghost Controls gate repair in Burbank typically runs $180–$450 depending on whether we’re replacing a sheared limit-stop gear, recalibrating a heat-warped TSS2, or rebuilding corroded hinges on a 1960s alley gate. We’re an independent Ghost Controls service provider, not manufacturer-affiliated, and we carry OEM motors, boards, and upgraded brass hardware on our trucks for same-day fixes across the 91521, 91522, 91523, and 91526 ZIP codes. Call (888) 416-1369 for a free estimate.

Call (888) 416-1369

Why Burbank Residents Choose Us for Ghost Controls Service

We’ve been fixing gates in Burbank for 14 years, and Ghost Controls has become one of the brands we know cold. Louis Barrera, our Founder and Master Technician, started this work after training at Los Angeles Trade-Technical College, where instructors drilled into us that every diagnosis needs evidence behind it. That habit stuck. These days, Louis and the Granite Gate team handle everything from a TSS1 swing operator that’s lost its calibration on a Magnolia Park bungalow to an SSP slide unit that’s grinding through a decomposed-granite driveway in the Rancho Equestrian district, plus Ghost Controls repair in Studio City when clients refer neighbors over the hill.

What separates us from the general handyman or the out-of-town contractor is simple: we only do gates. No garage doors, no fencing, no side projects. That focus means we stock Ghost Controls sales & service parts that other shops have to order, and we weld hinge brackets and fabricate gusset plates in-house instead of waiting on a subcontractor. Our 197 customer reviews averaging 4.7 stars tell us we’re doing something right. When your Ghost Controls operator throws an error code at 6 a.m. because last night’s Santa Ana gust caught your gate like a sail, you want a tech who’s seen that exact failure before, not someone reading a manual in your driveway.

Common Ghost Controls Gate Repair Problems We Solve in Burbank

TSS1 overswing and sheared limit-stop gears from Santa Ana winds. Burbank’s position in the San Fernando Valley makes it a wind tunnel when Santa Anas hit 50–80 mph. The TSS1’s nylon limit-stop gear wasn’t designed for gates that get pushed past their mechanical stops repeatedly. We replace it with an upgraded brass gear and reinforce the hinge brackets so the gate survives the next gust alert.
TSS2 travel calibration thrown by summer heat expansion. Sustained triple-digit temperatures in Burbank cause metal gate frames to expand and bind against posts. The TSS2’s force sensor reads that binding as an obstruction, and the travel limits drift day by day until the gate won’t fully open or close. We re-calibrate after the frame is freed and check for ground hardware that’s shifted in the heat.
SSP slide unit limit-switch corrosion from silica dust and dry-heat cycling. Burbank’s decomposed-granite driveways and decades of 100°F summers coat the SSP’s limit-switch contacts in fine particles. The result is intermittent “gate won’t close” errors that confuse homeowners and out-of-area techs alike. We clean the contact assemblies and replace them with sealed aftermarket switches when the OEM housings have cracked.
Rusted hinge pins on 1940s–1960s wrought iron alley gates. Burbank’s housing stock is full of side-yard and rear-alley gates with original hardware that’s 50–70 years old. The dry-heat cycling has corroded these hinges so badly that even a healthy Ghost Controls motor strains to move the gate. We cut out the old pins, weld in new stainless hardware, and realign the gate so the operator isn’t fighting friction it wasn’t designed for.
Wooden gate panel warping from extreme heat and UV exposure. Burbank’s intensity of sun exposure warps cedar and redwood gates faster than coastal cities. A warped panel binds in the jamb, and the Ghost Controls operator burns out its motor trying to push through. We plane or replace the panel, rehang it true, and match the operator’s force settings to the actual load.

Ghost Controls Service in Burbank: What Local Conditions Mean for Your Equipment

Burbank’s municipal building department operates independently of LA City and LA County, and that single fact changes how every Ghost Controls repair or installation plays out here. A contractor from Glendale or North Hollywood who assumes standard LA County rules apply can walk into a failed UL 325 compliance inspection because Burbank requires its own entrapment-sensor signage, specific photo-eye placement, and documented torque testing for automatic operators. We’ve seen DIY Ghost Controls installs fail on the first visit because a missing warning sticker, the kind that ships in the box and gets tossed, violated Burbank’s specific checklist. Louis and the Granite Gate team pre-check every job against Burbank’s requirements before we call for inspection. That means no re-inspection fees, no delayed move-ins for home sales, and no surprises for property managers on Alameda Ave who need their gate compliant yesterday. The entertainment industry folks who dominate Burbank’s residential market don’t have time for permit rework, and neither do we.

Ghost Controls Models & Products We Service in Burbank

We work on the full Ghost Controls residential and light-commercial lineup: the TSS1 and TSS2 swing gate operators, the SSP slide gate system, and the LSO linear actuator series. Our truck stocks OEM Ghost Controls replacement motors, control boards, and safety sensors for same-day Burbank repairs. For hinge rebuilds and hardware replacement on older gates, we use high-quality aftermarket bearings and stainless steel components that outlast the original zinc-plated parts in Burbank’s dry-heat environment. We’ll tell you straight whether a $180 gear swap gets you two more years or if the operator’s age and your gate’s condition point toward full replacement. No upsell, just the math.

Ghost Controls Service Pricing in Burbank

Ghost Controls repair costs in Burbank depend on what’s actually failed. Here’s what we typically see:

Limit-stop gear replacement (TSS1/TSS2): $180–$260
Control board or motor replacement: $320–$450
Hinge pin removal, weld repair, and stainless hardware: $200–$340
Full travel recalibration and safety sensor alignment: $150–$220
SSP slide unit track cleaning and limit-switch service: $180–$280

These ranges cover labor and parts. A full operator replacement on an existing gate runs higher, and we’ll walk you through that quote before ordering anything. Every estimate we provide in Burbank is free, and we don’t charge trip fees within the 91521–91526 area. Call (888) 416-1369 for an exact quote on your specific Ghost Controls system.

FAQs — Ghost Controls Gate Repair in Burbank

My Ghost Controls TSS1 keeps saying ‘error 7’ after the Santa Ana winds — is the motor burned out?
+

I want to add a Ghost Controls keypad to my alley gate, but Burbank has its own building department — do I need a permit?
+

My 1960s wrought-iron gate has rusted hinges and the Ghost Controls operator is struggling to move it — can you just replace the motor?
+

My Ghost Controls SSP slide gate on a rear alley in Burbank’s Magnolia Park neighborhood won’t close fully — is it the track?
+

I’m replacing my old Ghost Controls TSS2 with a new one — do I need a permit if it’s the same model?
+

Service Areas Near Burbank

We run Gate Access Control in Burbank calls daily, and our service radius extends to nearby communities including Ghost Controls service in View Park-Windsor Hills and Ghost Controls service in Corona. We also handle regular work in La Puente and Valinda for homeowners who need a gate specialist willing to travel. If you’re unsure whether we cover your address, call (888) 416-1369 and we’ll confirm.

Book Your Ghost Controls Service in Burbank Today

A gate that doesn’t open when you need it to isn’t a gate — it’s a wall. Let’s make it a gate again. Louis and the Granite Gate team are available for same-day Ghost Controls service across Burbank when the schedule allows, and we always start with a free, no-pressure estimate. Call (888) 416-1369 now.

Written by Louis Barrera, Owner at Granite Gate Repair California, serving Burbank since 2010.